Step-by-Step Wyze Smart Home Security Bundle Installation Guide

Step-by-Step Trustworthy Wyze Smart Home Security Bundle Installation Guide

Securing your home with Wyze smart devices is a smart choice for convenience, safety, and peace of mind. This guide provides a clear, step-by-step walkthrough to install key Wyze smart home security products, ensuring a smooth and trustworthy setup experience. Whether you are installing a Wyze Lock, Video Doorbell, or Robot Vacuum, this guide covers essential installation steps and tips to get your smart home security system up and running efficiently.

---

Wyze Lock Installation Guide

The Wyze Lock is designed to upgrade your existing deadbolt into a smart lock, allowing you to control access remotely and monitor your door’s status.

What’s Included in the Box?

• Wyze Lock
• Mounting Plate
• 4 Lock Adapters
• 4 AA Batteries
• Adhesive Strip
• Philips Screwdriver (required tool)

Installation Steps:

1. Prepare Your Door: Use the adhesive strip to hold the outside of the lock in place. Unlock your existing deadbolt. 2. Remove Old Hardware: Unscrew the thumb-latch and any back plates from your current deadbolt. 3. Attach Mounting Plate: Screw the mounting plate onto your door where the thumb-latch was, ensuring it is level but not over-tightened. 4. Select and Install Adapter: Use the Wyze app compatibility chart to find the correct adapter for your lock’s tailpiece and install it. 5. Mount the Wyze Lock: Remove the front plate of the lock, place the lock on the mounting plate, and align the knob with the adapter. 6. Test Alignment: Ensure the lock can turn freely. If not, rotate the thumb-latch 90 degrees and try again. 7. Secure and Power: Tighten the screws inside the battery compartment and install the 4 AA batteries, noting correct orientation. 8. Finalize Setup: Once installed, proceed to calibrate and set up the lock in the Wyze app.

Tip: Avoid over-tightening screws to prevent damage and difficult removal later.

---

Wyze Video Doorbell Installation Guide

The Wyze Video Doorbell enhances your home’s entryway with real-time video and two-way audio, allowing you to see and speak to visitors from anywhere.

What’s Included in the Box?

• Wyze Video Doorbell
• Wyze Chime
• Wall Plate and 30º Angled Wedge
• Screws, Expansion Tubes, Extension Wires, Jump Wire, Wire Caps
• Phillips Screwdriver (required tool)

Installation Steps:

1. Power Off: Turn off power to your existing mechanical doorbell at the electrical panel. 2. Document Wiring: Open your chime box and take a photo of the current wiring configuration. 3. Select Wiring Configuration: Use the Wyze app to select your wiring setup (2, 3, or 4+ wires). 4. Bypass Chime Circuit: Follow app instructions to bypass the chime using the jump wire or appropriate wiring. 5. Remove Old Doorbell: Detach your current doorbell and disconnect wires. 6. Mount Wall Plate or Wedge: Choose your preferred doorbell position (flat or angled) and install the wall plate or wedge. 7. Connect Wires: Attach extension wires to the doorbell, then connect to the house wiring using wire caps. 8. Restore Power: Turn the breaker back on and confirm the doorbell’s status light flashes yellow. 9. Attach Doorbell: Slide the doorbell onto the wall plate or wedge and secure it.

Safety Note: If you are uncomfortable working with electrical wiring, consult a licensed electrician.

---

Wyze Robot Vacuum Installation Guide

The Wyze Robot Vacuum automates floor cleaning with smart navigation and scheduling, making home maintenance effortless.

What’s Included in the Box?

• Wyze Robot Vacuum
• Charging Station and Power Adapter
• Dustbin and HEPA Filter
• Edge Brushes (2)
• Quick Start Guide and Manual

Installation Steps:

1. Prepare Vacuum: Attach the edge brushes to the vacuum’s bottom mounting pegs. 2. Set Up Charging Station: Connect the charging station to power and tuck in excess cord to prevent tangling. 3. Dock Vacuum: Place the vacuum on the charging station ensuring metal contacts touch. 4. Charge Fully: Wait for the vacuum’s lights to pulse yellow while charging and turn solid white when fully charged. 5. Complete Setup: Use the Wyze app to finalize setup and customize cleaning preferences.

Pro Tip: Position the charging station in an open area to allow easy docking and undocking.

---

Additional Tips for a Smooth Installation Experience

• Use the Wyze App: The app provides interactive setup guides, compatibility checks, and troubleshooting tips for each device.
• Check Compatibility: Before installation, verify your existing hardware (deadbolt, doorbell wiring) is compatible with Wyze products.
• Safety First: Always turn off power at the breaker when working with electrical wiring.
• Keep Tools Handy: A Phillips screwdriver is essential for most installations.
• Customer Support: Wyze offers support Monday through Sunday with phone and community resources for any installation questions.

---

“Wyze smart home devices combine ease of installation with powerful features, making home security accessible and reliable for everyone.”

---

Enhance your home security with Wyze smart devices seamlessly integrated.

---

By following this trustworthy, step-by-step guide, you can confidently install your Wyze smart home security bundle and enjoy the benefits of a connected, secure home.

---